低成本供应交流-Low-Cost AC Supply
abstract: the following application note discusses a low-cost solution to implement a 3v, 3.3v or 5v logic supply from ac power. it uses the max6330 shunt regulator which can supply up to 50ma as well as offering a reset output (power-on reset, por).
one often needs a low-cost logic supply for powering the mcu and related control circuitry in white goods products such as industrial controllers and sensors. those applications usually include 24vac, 115vac, or higher levels of ac power for conversion to 3.3v or 5.0v. (the following circuit suits applications that include 24vac. with proper safety precautions, it can also be applied to double-insulated white goods and other products that require a logic supply for control or monitoring functions.)
the simplest approach for generating low-current logic levels from an ac source is to apply the rectified and filtered ac input to a high-input-voltage linear regulator. but, power dissipation in the regulator can be considerable, even for modest load currents. a standard shunt regulator also dissipates notable power in the limiting resistor. a switching regulator minimizes power dissipation, but that type may not be practical for cost-sensitive designs.
as an alternative, consider an ac-coupled approach to reduce the power dissipation in linear or shunt-regulator designs. to transfer energy to the regulator with negligible power loss, use a coupling capacitor in conjunction with an ic containing a shunt regulator and power-on reset (figure 1). available with 50ma maximum output-current capability in 3.0v, 3.3v, and 5.0v shunt-voltage versions, ic1 also includes a power-on-reset (por) function. because ic1 is an active shunt (vs. a passive zener diode) one must rectify the ac voltage before applying it. typically, a capacitor follows the rectifier to hold the charge during off cycles. as shown, a simple half wave rectifier is used to save cost.
figure 1. this sot23 ic with low-cost external components provides a low-cost combination of power-on reset and efficient logic display.
c1 is the transfer capacitor and c2 stores energy. d1 acts as a half-wave rectifier, and d2 discharges the transfer capacitor during negative cycles. r1 limits surge current during the discharge of c1, and (if applicable) during high-voltage transient testing.
several simplifications help to approximate the available output current. assume zero forward drops in the diodes, and a zero shunt voltage in the ic regulator. with (for example) a 60hz sinusoidal input of 24vrms amplitude (vpeak = 33.94v), you can then calculate as follows:
peak current in c1 is ipeak(c1) = c1(dvs/dt) = c1[vpeak(dsin(ωt)/dt)] = c1[ωvpeakcos(ωt)] = c1ωvpeak. thus, with c1 = 3.0µf, ω= 377.1 radians/sec, and vpeak = 33.9v, ipeak = 38.4ma. rms charge current (irms) in c1 is thus, for t = 16.7msec, irms = 19.1ma.
by adjusting the value of c1 you can limit peak current levels to the level of maximum max6330 shunt current (50ma), while achieving an output of 20ma or so. the voltage rating of c1 should be able to withstand the maximum input voltage.
because peak currents are limited to ipeak, practically any small-signal diode can serve as the half-wave rectifier (d1). d2 discharges c1 during the negative portion of the cycle. the current rating of d2 depends on the value of vpeak and the selected value (50ω) of surge-limiting resistor r1. the maximum reverse voltage at d1 and d2 is (vshunt + vdiode).
c2 acts as a storage capacitor that maintains load current during the negative portion of the cycle. to calculate its value, use the following approximation based on the allowable level of ripple voltage (vripple): c2 = (iload × t/2)/vripple. with vripple = 150mv, t/2 = 8.3msec, and iload = 10ma, c2 = 550µf. a similar version of this article appeared in the may 16, 2002 issue of edn magazine.
安防系统入侵报警系统设计原理及应用
马云早已入局推出多种区块链平台，新人EBIT区块链简单而务实
消防泵控制柜和控制箱中间应该如何接线
Pixelworks携手HMD Global为诺基亚手机带来卓越显示及视频性能
联通又有重要人事变动,划小改革再深入?
低成本供应交流-Low-Cost AC Supply
Mobileye发布首个纯视觉智能车速辅助系统
用于钠金属电池的NASICON固态电解质的超快合成
介绍一下几种常见常用的SMT贴片机的吸嘴材质
WT6900G-24SS离线语音识别芯片在洗衣机中的应用
基于Virtex-5技术实现AURORA协议的串行传输系统的设计
失败是成功之母，一名开发工程师的工作经历
变压器T11/T12的作用解析
2023储能EPC/系统中标规模飙升：突破88GWh大关
精谱测控无纺布污点在线检测系统检测原理
Cuk升降压DC-DC的工作路径和关键公式推导
人才是企业动力—Enclustra十月欧洲招聘会活动全纪录
2018中国（深圳）集成电路创新应用高峰论坛落幕 AI成全场焦点
使用 ToF 传感器进行距离测量和手势识别的基本原理
N32系列MCU产品芯生态
one often needs a low-cost logic supply for powering the mcu and related control circuitry in white goods products such as industrial controllers and sensors. those applications usually include 24vac, 115vac, or higher levels of ac power for conversion to 3.3v or 5.0v. (the following circuit suits applications that include 24vac. with proper safety precautions, it can also be applied to double-insulated white goods and other products that require a logic supply for control or monitoring functions.)
the simplest approach for generating low-current logic levels from an ac source is to apply the rectified and filtered ac input to a high-input-voltage linear regulator. but, power dissipation in the regulator can be considerable, even for modest load currents. a standard shunt regulator also dissipates notable power in the limiting resistor. a switching regulator minimizes power dissipation, but that type may not be practical for cost-sensitive designs.
as an alternative, consider an ac-coupled approach to reduce the power dissipation in linear or shunt-regulator designs. to transfer energy to the regulator with negligible power loss, use a coupling capacitor in conjunction with an ic containing a shunt regulator and power-on reset (figure 1). available with 50ma maximum output-current capability in 3.0v, 3.3v, and 5.0v shunt-voltage versions, ic1 also includes a power-on-reset (por) function. because ic1 is an active shunt (vs. a passive zener diode) one must rectify the ac voltage before applying it. typically, a capacitor follows the rectifier to hold the charge during off cycles. as shown, a simple half wave rectifier is used to save cost.
figure 1. this sot23 ic with low-cost external components provides a low-cost combination of power-on reset and efficient logic display.
c1 is the transfer capacitor and c2 stores energy. d1 acts as a half-wave rectifier, and d2 discharges the transfer capacitor during negative cycles. r1 limits surge current during the discharge of c1, and (if applicable) during high-voltage transient testing.
several simplifications help to approximate the available output current. assume zero forward drops in the diodes, and a zero shunt voltage in the ic regulator. with (for example) a 60hz sinusoidal input of 24vrms amplitude (vpeak = 33.94v), you can then calculate as follows:
peak current in c1 is ipeak(c1) = c1(dvs/dt) = c1[vpeak(dsin(ωt)/dt)] = c1[ωvpeakcos(ωt)] = c1ωvpeak. thus, with c1 = 3.0µf, ω= 377.1 radians/sec, and vpeak = 33.9v, ipeak = 38.4ma. rms charge current (irms) in c1 is thus, for t = 16.7msec, irms = 19.1ma.
by adjusting the value of c1 you can limit peak current levels to the level of maximum max6330 shunt current (50ma), while achieving an output of 20ma or so. the voltage rating of c1 should be able to withstand the maximum input voltage.
because peak currents are limited to ipeak, practically any small-signal diode can serve as the half-wave rectifier (d1). d2 discharges c1 during the negative portion of the cycle. the current rating of d2 depends on the value of vpeak and the selected value (50ω) of surge-limiting resistor r1. the maximum reverse voltage at d1 and d2 is (vshunt + vdiode).
c2 acts as a storage capacitor that maintains load current during the negative portion of the cycle. to calculate its value, use the following approximation based on the allowable level of ripple voltage (vripple): c2 = (iload × t/2)/vripple. with vripple = 150mv, t/2 = 8.3msec, and iload = 10ma, c2 = 550µf. a similar version of this article appeared in the may 16, 2002 issue of edn magazine.
安防系统入侵报警系统设计原理及应用
马云早已入局推出多种区块链平台，新人EBIT区块链简单而务实
消防泵控制柜和控制箱中间应该如何接线
Pixelworks携手HMD Global为诺基亚手机带来卓越显示及视频性能
联通又有重要人事变动,划小改革再深入?
低成本供应交流-Low-Cost AC Supply
Mobileye发布首个纯视觉智能车速辅助系统
用于钠金属电池的NASICON固态电解质的超快合成
介绍一下几种常见常用的SMT贴片机的吸嘴材质
WT6900G-24SS离线语音识别芯片在洗衣机中的应用
基于Virtex-5技术实现AURORA协议的串行传输系统的设计
失败是成功之母，一名开发工程师的工作经历
变压器T11/T12的作用解析
2023储能EPC/系统中标规模飙升：突破88GWh大关
精谱测控无纺布污点在线检测系统检测原理
Cuk升降压DC-DC的工作路径和关键公式推导
人才是企业动力—Enclustra十月欧洲招聘会活动全纪录
2018中国（深圳）集成电路创新应用高峰论坛落幕 AI成全场焦点
使用 ToF 传感器进行距离测量和手势识别的基本原理
N32系列MCU产品芯生态