Using DS2148/348 as Repeater
abstract: application note 387 describes the use of the dallas semiconductor/maxim ds2148/ds21348 as a t1 or e1 repeater. a simple circuit diagram shows typical connections. configurations for hardware mode and software mode are also provided.
introductionthis application note describes the register settings for dallas semiconductor's ds2148 and ds21348 (e1/t1/j1 line interface units) as a repeater for t1 or e1 operation. this can be accomplished with the device in either hardware or software mode.
the receive sensitivity for these two lius is programmable and is as much as -36db for t1 applications and -43db for e1 applications.
to simplify the design, it is recommended to use a 2.048mhz oscillator and use the internal register settings of the ds2148 and the ds21348 to convert the mclk to 1.544mhz for t1 applications.
figure 1. typical t1/e1 repeater application.
the configuration settings of the ds2148 or the ds21348 in hardware mode are:
hardware mode settings for t1 hardware mode settings for e1
mclk = 2.048mhz mclk = 2.048mhz
bis1 = 1, bis0 = 1 bis1 = 1, bis0 = 1
ces = 0 ces = 0
dja = 0 or 1 (application dependent) dja = 0 or 1 (application dependent)
hbe = 1 hbe = 1
jas = 0 or 1 (application dependent) jas = 0 or 1 (application dependent)
nrze = 0 nrze = 0
tpd = 0 tpd = 0
l2 = l1 = l0 = 0 l2/l1/l0 (application dependent)
tx1 = 0, tx0 = 0 tx1 = 0, tx0 = 0
loop1 = 0, loop0 = 0 loop1 = 0, loop0 = 0
egl = 1, ets = 1 (limited long haul)
egl = 0, ets = 1 (long haul) egl = 0, ets = 0 (short haul)
egl = 1, ets = 0 (long haul)
mm1 = 0, mm0 = 0 mm1 = 0, mm0 = 0
rt1 = 1, rt0 = 0 (internal rx side, 100Ω enabled) rt1 = 0, rt0 = 1 (internal rx side, 120Ω enabled)
rt1 = 1, rt0 = 1 (internal rx side, 75Ω enabled)
jamux = 1, ets = 1 jamux = 1, ets = 0
the configuration settings of the ds2148 or the ds21348 in software mode are:
software mode register settings for t1 software mode register settings for e1
mclk = 2.048mhz mclk = 2.048mhz
ccr1 (00h) ccr1.7 = 1
ccr1.6 = 0
ccr1.3 = 1
ccr1.1 = 1 ccr1 (00h) ccr1.7 = 0
ccr1.6 = 0
ccr1.3 = 1
ccr1.1 = 1
ccr2 (01h) ccr2.3 = 1
ccr2.2 = 1
ccr2.1 = 0
ccr2.0 = 0 ccr2 (01h) ccr2.3 = 1
ccr2.2 = 1
ccr2.1 = 0
ccr2.0 = 0
ccr4 (03h) ccr4.7 = ccr4.6 = ccr4.5 = 0
ccr4.1 (application dependent)
ccr4.0 = 0 ccr4 (03h) ccr4.7, ccr4.6, and ccr4.5 (application dependent)
ccr4.1 (application dependent)
ccr4.0 = 0
ccr5 (04h) ccr5.5 = 0, ccr5.4 = 0
ccr5.1 = 1, ccr5.0 = 0
(internal rx side, 100Ω enabled) ccr5 (04h) ccr5.5 = 0, ccr5.4 = 0
ccr5.1 = 0, ccr5.0 = 1
(internal rx side, 120Ω enabled)
ccr5.1 = 1, ccr5.0 = 1
(internal rx side, 75Ω enabled)
IBM李瑞梅：Be Equal——大音希声，大象无形
介绍示波器频率响应、FFT功能以及探头衰减比对测量
喜报！数千家物联网企业中评选，全视通荣膺“物联网场景应用品牌企业”奖项
采用LMV1090放大器和AT89C51单片机改进型噪声抑制话音采集方案
对象存储的优势有哪些？
Using DS2148/348 as Repeater
关于LabVIEW编程实例介绍和说明
芯片巨头美光宣布向客户交付176层闪存
安科瑞交流多回路智能电量采集监控装置在河南某高速公路项目的应用
基于简单微控制器（MCU）的系统：联觉编码器
面对示波器的波形死区，工程师们怎么选择
续流二极管选择次级的基础知识介绍
iphone8或将回归初代设计，以水滴形设计以致初代iphone
中国科学院微纳生物机器人治疗肿瘤方面取得新突破
三星Note20怎么样？号称2020年三星安卓机皇 S-Pen没缺席
极空间私有云TV新版发布，蓝光影音功能再进化
荣耀8和荣耀v8有什么区别，荣耀8和荣耀v8评测对比，你会选谁？
华为P10上手评测：我真的想放弃iPhone 7了
有颜值更有好颜色 这些手机如今最受欢迎
无线电测向及ＰＪ－８０型测向机电路
introductionthis application note describes the register settings for dallas semiconductor's ds2148 and ds21348 (e1/t1/j1 line interface units) as a repeater for t1 or e1 operation. this can be accomplished with the device in either hardware or software mode.
the receive sensitivity for these two lius is programmable and is as much as -36db for t1 applications and -43db for e1 applications.
to simplify the design, it is recommended to use a 2.048mhz oscillator and use the internal register settings of the ds2148 and the ds21348 to convert the mclk to 1.544mhz for t1 applications.
figure 1. typical t1/e1 repeater application.
the configuration settings of the ds2148 or the ds21348 in hardware mode are:
hardware mode settings for t1 hardware mode settings for e1
mclk = 2.048mhz mclk = 2.048mhz
bis1 = 1, bis0 = 1 bis1 = 1, bis0 = 1
ces = 0 ces = 0
dja = 0 or 1 (application dependent) dja = 0 or 1 (application dependent)
hbe = 1 hbe = 1
jas = 0 or 1 (application dependent) jas = 0 or 1 (application dependent)
nrze = 0 nrze = 0
tpd = 0 tpd = 0
l2 = l1 = l0 = 0 l2/l1/l0 (application dependent)
tx1 = 0, tx0 = 0 tx1 = 0, tx0 = 0
loop1 = 0, loop0 = 0 loop1 = 0, loop0 = 0
egl = 1, ets = 1 (limited long haul)
egl = 0, ets = 1 (long haul) egl = 0, ets = 0 (short haul)
egl = 1, ets = 0 (long haul)
mm1 = 0, mm0 = 0 mm1 = 0, mm0 = 0
rt1 = 1, rt0 = 0 (internal rx side, 100Ω enabled) rt1 = 0, rt0 = 1 (internal rx side, 120Ω enabled)
rt1 = 1, rt0 = 1 (internal rx side, 75Ω enabled)
jamux = 1, ets = 1 jamux = 1, ets = 0
the configuration settings of the ds2148 or the ds21348 in software mode are:
software mode register settings for t1 software mode register settings for e1
mclk = 2.048mhz mclk = 2.048mhz
ccr1 (00h) ccr1.7 = 1
ccr1.6 = 0
ccr1.3 = 1
ccr1.1 = 1 ccr1 (00h) ccr1.7 = 0
ccr1.6 = 0
ccr1.3 = 1
ccr1.1 = 1
ccr2 (01h) ccr2.3 = 1
ccr2.2 = 1
ccr2.1 = 0
ccr2.0 = 0 ccr2 (01h) ccr2.3 = 1
ccr2.2 = 1
ccr2.1 = 0
ccr2.0 = 0
ccr4 (03h) ccr4.7 = ccr4.6 = ccr4.5 = 0
ccr4.1 (application dependent)
ccr4.0 = 0 ccr4 (03h) ccr4.7, ccr4.6, and ccr4.5 (application dependent)
ccr4.1 (application dependent)
ccr4.0 = 0
ccr5 (04h) ccr5.5 = 0, ccr5.4 = 0
ccr5.1 = 1, ccr5.0 = 0
(internal rx side, 100Ω enabled) ccr5 (04h) ccr5.5 = 0, ccr5.4 = 0
ccr5.1 = 0, ccr5.0 = 1
(internal rx side, 120Ω enabled)
ccr5.1 = 1, ccr5.0 = 1
(internal rx side, 75Ω enabled)
IBM李瑞梅：Be Equal——大音希声，大象无形
介绍示波器频率响应、FFT功能以及探头衰减比对测量
喜报！数千家物联网企业中评选，全视通荣膺“物联网场景应用品牌企业”奖项
采用LMV1090放大器和AT89C51单片机改进型噪声抑制话音采集方案
对象存储的优势有哪些？
Using DS2148/348 as Repeater
关于LabVIEW编程实例介绍和说明
芯片巨头美光宣布向客户交付176层闪存
安科瑞交流多回路智能电量采集监控装置在河南某高速公路项目的应用
基于简单微控制器（MCU）的系统：联觉编码器
面对示波器的波形死区，工程师们怎么选择
续流二极管选择次级的基础知识介绍
iphone8或将回归初代设计，以水滴形设计以致初代iphone
中国科学院微纳生物机器人治疗肿瘤方面取得新突破
三星Note20怎么样？号称2020年三星安卓机皇 S-Pen没缺席
极空间私有云TV新版发布，蓝光影音功能再进化
荣耀8和荣耀v8有什么区别，荣耀8和荣耀v8评测对比，你会选谁？
华为P10上手评测：我真的想放弃iPhone 7了
有颜值更有好颜色 这些手机如今最受欢迎
无线电测向及ＰＪ－８０型测向机电路