数字控制移相-Digitally Control Phase
abstract: the application note describes using a digital potentiometer, passive components such as resistors and capacitors, and an operational amplifier to build a digitally controlled phase-shift circuit. although written specifically for the ds1669, it is applicable for any potentiometer from dallas semiconductor or maxim, which has the bandwidth to carry an audio signal.
introductionaltering the phase response of a signal without changing its amplitude characteristics is commonly performed using an allpass filter, as in figure 1. the response of this circuit is given by
figure 1. a simple phase shift circuit can be implemented using an allpass filter.
as the signal frequency varies from dc to infinity, the phase shift will vary from 0 to +180 degrees. you can also see that by varying r1, the phase shift at a given frequency will vary likewise. if the position of r1 and c1 are reversed, as in figure 2, the transfer function becomes
and the phase then varies from -180 to 0 degrees. the phase shift this circuit realizes at any given frequency can be found by
where w is the frequencies in rad/s, or 2×pi×f, when f is in hertz. as a practical matter, most circuits of this type can comfortably cover a phase range of about 120 degrees with real op amps and components.
figure 2. this allpass filter circuit swaps the location of r1 and c1.
controlling the phase shift digitallythis circuit implementation is well suited to using digital potentiometers in place of r1, as shown in figure 3. with this circuit, optimized for phase-shifting over the audio range, the phase at a given frequency is now under control of a digital signal. the ds1669 used here can have its wiper position set by using a single digital control line to cause the wiper position to increment upon each low-going pulse, until it reaches the upper end of the pot, when it will reverse direction and decrement. supplying a clock to this digital control input will cause the phase to constantly sweep, an effect commonly used in popular recordings today. note that since this is a single supply circuit, the digital potentiometer is biased at ½vcc.
figure 3. replacing r1 with a digital potentiometer causes the phase shift the circuit realizes to be under digital control.
a complete audio phase shift effectseveral of these phase shift sections can be cascaded to realize greater phase shifts. dual, quad, or hex digital potentiometers can be used to control all sections under control of a microprocessor, as shown in the phase shifter/stereo synthesizer example of figures 4-8. the ds1806 hex digital potentiometers' wiper positions are under control of a simple three-wire digital interface, which clocks the wiper position settings into the device over its dq line, while the /rst line is high. when /rst goes low, the wiper is positioned at the new setting.
figure 4. the input stage to the phase shifter provides a buffered, ac coupled signal.
figure 5. since this is a single-supply circuit, this circuitry creates a virtual, or signal, ground for the rest of the circuitry. u4 is a tlc274 single-supply op amp.
figure 6. one stage (of four) which implements the phase shift. this is the same circuit as figure 3, but r1 of that circuit is replaced by a section of a hex potentiometer, referred to here as the stage pot.
figure 7. four sections of the ds1806 are used to control the phase shift of each stage under microprocessor control. note that two pot sections are left over, available perhaps for use as level controls.
figure 8. the final output stage consists of a mixer which combines the outputs from the various stages to provide the familiar phasor effect, as well as a psuedo-stereo output.
this circuit appeared in edn magazine's design ideas, february 15, 1996, pp.114-116.
EDA的发展对开发人员和用户的影响
一文解析机器人在中国的兴起与发展
英伟达初创加速计划全球成员破8,000，助力塑造全球AI初创企业生态格局
Bourns推出两款新型TVS二极管浪涌保护系列
DeepSpark 开源社区百大应用开放平台23.06版本正式发布
数字控制移相-Digitally Control Phase
OPPO Enco Air2 Pro怎么样：为你带来沉浸式听觉
电瓶寿命检测中过机总是出现内阻过大的问题是什么原因
T900数传在无人机自动机场上应用解析
ADDere激光混合焊接系统的介绍
主动红外入侵探测器的安装环境_主动红外探测器的安装注意事项
联通上线5G升级包 9.9元即可畅享5G流量
嵌入式状态监测与故障诊断装置设计
智能硬件创新设计行业走势及战略布局
基于LINUX的嵌入式浏览器的设计与实现
华为史上最好看手机今天发布 叫板iPhone7
带鱼屏+升降镜头？颜值超高，但看到处理器？再见？
适用于传输少量数据的蓝牙低能耗技术
IBM助力客户斩获多项IDC中国未来企业大奖
三种write mode，你真的理解吗？
introductionaltering the phase response of a signal without changing its amplitude characteristics is commonly performed using an allpass filter, as in figure 1. the response of this circuit is given by
figure 1. a simple phase shift circuit can be implemented using an allpass filter.
as the signal frequency varies from dc to infinity, the phase shift will vary from 0 to +180 degrees. you can also see that by varying r1, the phase shift at a given frequency will vary likewise. if the position of r1 and c1 are reversed, as in figure 2, the transfer function becomes
and the phase then varies from -180 to 0 degrees. the phase shift this circuit realizes at any given frequency can be found by
where w is the frequencies in rad/s, or 2×pi×f, when f is in hertz. as a practical matter, most circuits of this type can comfortably cover a phase range of about 120 degrees with real op amps and components.
figure 2. this allpass filter circuit swaps the location of r1 and c1.
controlling the phase shift digitallythis circuit implementation is well suited to using digital potentiometers in place of r1, as shown in figure 3. with this circuit, optimized for phase-shifting over the audio range, the phase at a given frequency is now under control of a digital signal. the ds1669 used here can have its wiper position set by using a single digital control line to cause the wiper position to increment upon each low-going pulse, until it reaches the upper end of the pot, when it will reverse direction and decrement. supplying a clock to this digital control input will cause the phase to constantly sweep, an effect commonly used in popular recordings today. note that since this is a single supply circuit, the digital potentiometer is biased at ½vcc.
figure 3. replacing r1 with a digital potentiometer causes the phase shift the circuit realizes to be under digital control.
a complete audio phase shift effectseveral of these phase shift sections can be cascaded to realize greater phase shifts. dual, quad, or hex digital potentiometers can be used to control all sections under control of a microprocessor, as shown in the phase shifter/stereo synthesizer example of figures 4-8. the ds1806 hex digital potentiometers' wiper positions are under control of a simple three-wire digital interface, which clocks the wiper position settings into the device over its dq line, while the /rst line is high. when /rst goes low, the wiper is positioned at the new setting.
figure 4. the input stage to the phase shifter provides a buffered, ac coupled signal.
figure 5. since this is a single-supply circuit, this circuitry creates a virtual, or signal, ground for the rest of the circuitry. u4 is a tlc274 single-supply op amp.
figure 6. one stage (of four) which implements the phase shift. this is the same circuit as figure 3, but r1 of that circuit is replaced by a section of a hex potentiometer, referred to here as the stage pot.
figure 7. four sections of the ds1806 are used to control the phase shift of each stage under microprocessor control. note that two pot sections are left over, available perhaps for use as level controls.
figure 8. the final output stage consists of a mixer which combines the outputs from the various stages to provide the familiar phasor effect, as well as a psuedo-stereo output.
this circuit appeared in edn magazine's design ideas, february 15, 1996, pp.114-116.
EDA的发展对开发人员和用户的影响
一文解析机器人在中国的兴起与发展
英伟达初创加速计划全球成员破8,000，助力塑造全球AI初创企业生态格局
Bourns推出两款新型TVS二极管浪涌保护系列
DeepSpark 开源社区百大应用开放平台23.06版本正式发布
数字控制移相-Digitally Control Phase
OPPO Enco Air2 Pro怎么样：为你带来沉浸式听觉
电瓶寿命检测中过机总是出现内阻过大的问题是什么原因
T900数传在无人机自动机场上应用解析
ADDere激光混合焊接系统的介绍
主动红外入侵探测器的安装环境_主动红外探测器的安装注意事项
联通上线5G升级包 9.9元即可畅享5G流量
嵌入式状态监测与故障诊断装置设计
智能硬件创新设计行业走势及战略布局
基于LINUX的嵌入式浏览器的设计与实现
华为史上最好看手机今天发布 叫板iPhone7
带鱼屏+升降镜头？颜值超高，但看到处理器？再见？
适用于传输少量数据的蓝牙低能耗技术
IBM助力客户斩获多项IDC中国未来企业大奖
三种write mode，你真的理解吗？