Interfacing the MAX187 to the
abstract: this application note describes how to interface the max187 to the tms320c3x dsp ev module. this app note can also be used as an example to interface other maxim ics to the tms320 ev module. example assembly code is provided.
overviewthe max187 12-bit adc can be interfaced to texas instruments' tms320c30 dsp via serial interface. the interface uses three wires plus ground. this application note explains how to interface the max187 evaluation kit to the tms320c3x evaluation module.
the example program was assembled using the tms320c3x/4x coff assembler version 4.50 and the tms320c3x/4f coff linker version 4.50 (the assembler and linker are copyright 1987-1992 texas instruments incorporated).
figure 1. max187-tms320 interface.
figure 2. max187-tms320 timing.
larger image
figure 3. listing.
interfacing the max187 evkit to the tms320c3x evmmaxim's max187 evaluation kit can be interfaced to texas instruments' tms320c3x evaluation module as follows:
solder a 2-x-5-pin berg strip into the prototype area. connect it as indicated in the table below. connect a +5v power supply to the max187. use a 10-pin ribbon cable to connect the tms320c3x evm to the max187evkit. run the demo software.
ribbon-cable signals
pin max187 tms320 pin max187 tms320
1 dgnd gnd 2 dout fsr1
3 not used 4 dout dr1
5 not used 6 not used
7 not used 8 cs xf1
9 sclk clkr1 10 dgnd gnd
how it worksthe demo software configures the tms320c30 so that fsr1 and dr1 are inputs and clkr1 and xf1 are outputs. the software uses the xf1 output to initiate a conversion. the xf1 pulse drives the max187 chip-select input. the clkr1 output provides the serial clock to the max187. data output from the max187 is received on the dr1 input. the fsr1 frame start signal is also tied to the data output, so that the start bit from the max187 marks the beginning of the serial frame.
to read the max187, the software drives the xf1 output low and then waits 10µsec to allow time for the conversion. then, the software enables the serial receive clock. the max187 sends its start bit, followed by the serial data. the demo software polls the serial receiver until a complete frame has been received. because only 12 of the 16 bits are significant, the demo software right-justifies the significant bits and removes the start bit; then it writes the 12-bit word to the evm host data port.
电气火灾监控系统在酒店的设计与应用
Microdrop微滴式数字PCR检测系统，实现低成本的无创检测
贸泽电子见证同济大学翼驰车队惊艳FSG——霍根海姆的中国速度
半导体供应链本土化前景可期
颜值与实力兼具的蓝牙耳机：这五款蓝牙耳机最好用！
Interfacing the MAX187 to the
IC设计新战场，DPU竞争才刚开始
中兴BladeA2S评测 适合学生党与备机党
2016年HTC手机市场出货量惨淡 都扑在Vive VR上来了
嵌入式系统应用实例的详细资料介绍
GaN成为打造高功率密度器件的天然之选
电阻触摸屏的校准算法
云计算和AI或成谷歌新的切入点
关于数据中心的云计算可行性的CIO指南
SMSC发表高速USB 2.0连接方案—USB3803集线器
可以和路人交流的自动驾驶汽车
带电作业太危险,高空输电线路进行带电作业的“特种兵”机器人发布
中国科研团队研制出可医用的纳米机器人
Linux诊断系统故障命令dmesg详解
买macbookpro后悔了,Mac太贵而且端口极其不便捷
overviewthe max187 12-bit adc can be interfaced to texas instruments' tms320c30 dsp via serial interface. the interface uses three wires plus ground. this application note explains how to interface the max187 evaluation kit to the tms320c3x evaluation module.
the example program was assembled using the tms320c3x/4x coff assembler version 4.50 and the tms320c3x/4f coff linker version 4.50 (the assembler and linker are copyright 1987-1992 texas instruments incorporated).
figure 1. max187-tms320 interface.
figure 2. max187-tms320 timing.
larger image
figure 3. listing.
interfacing the max187 evkit to the tms320c3x evmmaxim's max187 evaluation kit can be interfaced to texas instruments' tms320c3x evaluation module as follows:
solder a 2-x-5-pin berg strip into the prototype area. connect it as indicated in the table below. connect a +5v power supply to the max187. use a 10-pin ribbon cable to connect the tms320c3x evm to the max187evkit. run the demo software.
ribbon-cable signals
pin max187 tms320 pin max187 tms320
1 dgnd gnd 2 dout fsr1
3 not used 4 dout dr1
5 not used 6 not used
7 not used 8 cs xf1
9 sclk clkr1 10 dgnd gnd
how it worksthe demo software configures the tms320c30 so that fsr1 and dr1 are inputs and clkr1 and xf1 are outputs. the software uses the xf1 output to initiate a conversion. the xf1 pulse drives the max187 chip-select input. the clkr1 output provides the serial clock to the max187. data output from the max187 is received on the dr1 input. the fsr1 frame start signal is also tied to the data output, so that the start bit from the max187 marks the beginning of the serial frame.
to read the max187, the software drives the xf1 output low and then waits 10µsec to allow time for the conversion. then, the software enables the serial receive clock. the max187 sends its start bit, followed by the serial data. the demo software polls the serial receiver until a complete frame has been received. because only 12 of the 16 bits are significant, the demo software right-justifies the significant bits and removes the start bit; then it writes the 12-bit word to the evm host data port.
电气火灾监控系统在酒店的设计与应用
Microdrop微滴式数字PCR检测系统，实现低成本的无创检测
贸泽电子见证同济大学翼驰车队惊艳FSG——霍根海姆的中国速度
半导体供应链本土化前景可期
颜值与实力兼具的蓝牙耳机：这五款蓝牙耳机最好用！
Interfacing the MAX187 to the
IC设计新战场，DPU竞争才刚开始
中兴BladeA2S评测 适合学生党与备机党
2016年HTC手机市场出货量惨淡 都扑在Vive VR上来了
嵌入式系统应用实例的详细资料介绍
GaN成为打造高功率密度器件的天然之选
电阻触摸屏的校准算法
云计算和AI或成谷歌新的切入点
关于数据中心的云计算可行性的CIO指南
SMSC发表高速USB 2.0连接方案—USB3803集线器
可以和路人交流的自动驾驶汽车
带电作业太危险,高空输电线路进行带电作业的“特种兵”机器人发布
中国科研团队研制出可医用的纳米机器人
Linux诊断系统故障命令dmesg详解
买macbookpro后悔了,Mac太贵而且端口极其不便捷